Salsbury-industries 40000 Series Heavy Duty Plastic Lockers User Manual download pdf

Heavy Duty Plastic Lockers – 40000 Series

Locker Installation Instructions

Thank you for selecting 40000 Series Heavy Duty Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a

good investment. These instructions are intended to assist you in the assembly, placement, and anchoring of your lockers. Individual job conditions

will dictate whether the lockers must be anchored to the wall, the floor, or both.

Separate parts from packaging and make sure all parts are accounted for before discarding any packaging

material. If any parts are missing, do not begin installation until you obtain the missing parts.

Lockers should be installed in a climate-controlled environment and shielded from direct sunlight. All lockers

must be either secured against a wall or installed back-to-back (for island configuration).

Make sure all floors and walls are clean and smooth. Remove loose impediments, such as protruding nails, and

other debris which could affect installation. The lockers must be square and level and floor supported or they will

not operate properly. A locker that is square may not be level, so be sure to check both.

Review your locker layout drawings and verify the number of lockers and components before beginning

installation.

Carefully lift lockers at the base when moving and positioning. Do not drag the lockers.

LOCKER BASES MUST BE SQUARE AND LEVEL, AND ANCHORED TO THE FLOOR BEFORE THE LOCKERS ARE

INSTALLED. THE LOCKERS WILL NOT OPERATE PROPERLY IF THE BASE IS NOT SQUARE AND LEVEL AND

NOT FLOOR-SUPPORTED. A LOCKER BASE THAT IS SQUARE MAY NOT BE LEVEL, SO BE SURE TO CHECK

BOTH.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY

DAMAGE AND WILL VOID THE LOCKER WARRANTY.

Tools required: Tape measure - - - 9/32” drill bit - - - hammer drill for drilling into concrete - - - 6’ level and shims - - - power drill - - - Phillips driver

bit - - - clamps - - - 3/16” masonry drill bit (6” long minimum) - - - circular saw - - - right-angle power drill - - - chalk and string.

The following tips may be helpful: A string line along the top and bottom of the lockers may be used to help in alignment. If shims are required

after locker installation is complete, remove obstructive screws, apply the shims, then replace the screws. Avoid twisting the locker frames when

applying shims.

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

www.lockers.com engineering

@lockers.com

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

1 2 3 4 5 6

Base Installation 2

Summary of Contents

Page 1

Heavy Duty Plastic Lockers – 40000 Series Locker Installation Instructions Thank you for selecting 40000 Series Heavy Duty Plastic Lockers. We are

Page 2 - Base Installation

Heavy Duty Plastic Lockers – 40000 Series Locker Base Installation Instructions IMPORTANT: Make sure the base is square and level before anchori

Page 3

Heavy Duty Plastic Lockers – 40000 Series Locker Installation Instructions Note: Refer to your layouts for proper locker position. The first loc

Page 4

Heavy Duty Plastic Lockers – 40000 Series Sloping Hood Installation Instructions The Slope Tops are shipped in two (2) standard lengths of 1-wide

Page 5

Heavy Duty Plastic Lockers – 40000 Series Sloping Hood Installation Instructions LOCATION OF HOLES IN WALL STRIPS 1. Fit the groove of the fir

Page 6

Heavy Duty Plastic Lockers – 40000 Series End Panel Installation Instructions 1. Drill five (5) 3/16” diameter holes through each of the exposed

Comments to this Manuals

No comments

Salsbury-industries 40000 Series Heavy Duty Plastic Lockers User Manual

Browse online or download User Manual for Furniture Salsbury-industries 40000 Series Heavy Duty Plastic Lockers. Salsbury Industries 40000 Series Heavy Duty Plastic Lockers User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Furniture Salsbury-industries 40000 Series Heavy Duty Plastic Lockers